This is just a personal list of Zigbee devices I use at home. The list is sorted in the order in which I bought the devices. You can tell this by the fact that I paid way too much for the first few devices before I got into the “AliExpress” game. 🙂
Helpful databases:
https://www.zigbee2mqtt.io/supported-devices
https://zigbee.blakadder.com/
| Manufacturer | Model | Type | Z2M | Paring | Battery/Powering | Best price I got it for | Comment |
|---|---|---|---|---|---|---|---|
| Blitzwolf | BW-SHP13 Smart Socket | Plug (incl. power measurement) | # | Pair this device with a long press (5 seconds) on the on/off button | 230v | 9,45€ | |
| Blitzwolf | BW-SHP15 Smart Socket | Plug (incl. power measurement) | # | Pair this device with a long press (5 seconds) on the on/off button | 230v | 8,98€ | |
| Germa | Plug | Plug | Pair this device with a long press (5 seconds) on the on/off button | 230v | 8,97€ | ||
| Ikea | TRÅDFRI Motion | Motion sensor | # | Press pairing button 4 times | 2xCR2032 | 9,99€ | |
| Ikea | TRÅDFRI Repeater | Signal Repeater | # | Push the reset button of the device with a paperclip for 5 seconds | 230v | ||
| Ikea | TRÅDFRI LED | LED bulb E27 | # | 230v | |||
| Ikea | TRÅDFRI Wireless dimmer | Dimmer / switch | I’ve actually never used it. | ||||
| Ikea | TRÅDFRI Steckdose | Plug | # | Press and hold the reset button until the white light starts fading | 230v | From my eight devices, one already died. | |
| Ikea | BADRING | Water Leakage Sensor | # | Press the pairing button 4 times within 5 seconds | 1xAAA | ||
| Ikea | E1743 | Dimmer / switch | # | Press the pairing button 4 times | 1xCR2032 | I’ve actually never used it. | |
| Müller-Licht | tint | LED bulb E14 | 230v | 15,00€ | |||
| Xiaomi Mijia | GZCGQ01LM | Light sensor | 11,75€ | Had no real use case for the device so far. | |||
| Aqara | MCCGQ11LM | Contact sensor | # | Press and hold the reset button on the device for +- 5 seconds (until the blue light starts blinking). | 1xCR1632 | 8,56€ | Somehow, this device loses the connection to my Zigbee network every few months, and reconnection always causes problems. |
| Aqara | WSDCGQ11LM | Temperature and humidity sensor | # | Press and hold the reset button on the device for +- 5 seconds (when the blue blinks, immediately release the button for pairing to start). | 1xCR2032 | 13,93€ | Somehow, this device loses the connection to my Zigbee network every few months, and reconnection always causes problems. |
| Aqara | SSM-U01 | Single Switch Module T1 (with neutral) | # | Press button on device for 8 seconds, or toggle external switch 5 times (if it does not work, continue toggling the switch). | 230v | 24,00€ | Supports rocker switch (bistable / Wippschalter) or rebound switch (monostable / Wipptaster). Switch mode can be changed via Zigbee2MQTT. FAQ. Manual. |
| Ledvance (ex. OSRAM) | SMART+ Gardenpole | LED Garden lighting | # | Turn light 5x for 5 sec on and 5 sec off | 230v | 34,99€ | |
| Ledvance | SMART+ BT TIBEA Pendant Tunable White | LED Pendant lamp | # | Turn light 5x for 5 sec on and 5 sec off | 230v | ||
| OSRAM (LIGHTIFY) | Classic A60 W clear | LED bulb E27 | Turn light 5x for 3 sec on and 5 sec off | 230v | 7,99€ | These bulbs can lead to problems in the Zigbee network. Cannot find the source anymore, where I’ve read this… | |
| Lidl | LIVARNO LUX HG06106C | LED bulb E27 | # | Check zigbee2mqtt docs | 230v | ||
| Lidl | SilverCrest HG06335/HG07310 | Motion sensor | # | Factory reset the motion detector by holding the reset button (little hole on the right side, not the button on the back) for 5 seconds. | In my experience, I had many issues pairing this device using Zigbee2MQTT. With ZHA it was always working on the first try. Also, it helped to remove the battery before paring. Very poorly performing motion detector… already replaced it. | ||
| Lidl | LIVARNO Smart Home Outdoor-LED-Band | LED Strip | # | Turn device on/off 3 times | 230v | Some LEDs are not working anymore. | |
| Lidl | LIVARNO home LED-Band | LED Strip | # | Turn device on/off 3 times | 230v | The LED controller makes a high-pitched noise, which is super annoying. After about 3 years, the controller stopped working completely. | |
| Philips | LWA001 | LED bulb E27 | # | Only by using the Philips RWL021 remote. Press on & off buttons on the remote for 5 seconds close to the lamp. (#) | 230v | ||
| Philips | RWL021 | Dimmer / switch | # | Factory reset the Hue dimmer switch by pressing and holding the setup button on the back for 10 seconds. | CR2450 | Can also be used to reset Zigbee devices of other brands.(#) | |
| Sonoff | SNZB-02D | Temperature and humidity sensor | # | Press pairing button for 5 seconds | CR2450 | 12,62€ | Somehow, this device loses the connection to my Zigbee network every few months. Check here for troubleshooting. I replaced it with another temp sensor. |
| Sonoff | ZBMINIL2 | Smart Switch (no neutral) | # | Press the pairing button for 5 seconds, until the signal LED flashes slowly. | 230v | 12,28€ | Supports rocker switch (Wippschalter) and push button (Wipptaster). To change mode, press the pairing button very fast three times (so fast that the relay does not get trigger while doing that) until the green LED flashes 3 times. |
| ONENUO | TH01Z | Temperature and humidity sensor | # | Press pairing button for 5 seconds (review) | 3xAAA | 11,13€ | Somehow, this device loses the connection to my Zigbee network every few months. That’s why I replaced it. |
| Wenzhi | WZ-M100-W | Presence sensor | # | Connect via USB cable and press pairing button for 5 seconds | 5v USB-C | 11,83€ | Device is spamming the network with default firmware. Device also works via ZHA via a custom quirk (see comments here). There is also a custom firmware, but it cannot be flashed via OTA. _TZE204_ztc6ggyl |
| Tuya | ZG-205Z/A | Presence sensor | # | Connect via USB cable and press pairing button for 5 seconds | 5v USB-C | 12,22€ | So far, the only Zigbee presence sensor, that is not spamming. _TZE200_2aaelwxk |
| Wenzhi | MTG275-ZB-RL | Presence sensor | # | Press and hold pairing button for more than 3 seconds | 230v | 17,64€ | Device is spamming the network. Check here. _TZE204_dtzziy1e |
| ONENUO | TS0207 | Water leak sensor | # | Press and hold pairing button until red LED is flashing | 2xAAA | 3,79€ | |
| eWeLink | SNZB-04 | Contact sensor | # | Press and hold the RESET button for 5 seconds till red LED flashes | 2xAAA | 2,29€ | |
| HEIMAN | HS1SA | Smoke detector | # | Press and hold the RESET button for 2 seconds till Test Button LED flashes green | 1x CR17335/CR123A | 15,79€ | |
| Tuya | PA-44Z | Smoke detector | # | Press and hold test/mute button for 10 seconds till LED flashes quickly | 1x CR17335 | 6,39€ | Low battery alert: ≤20% |
| Tuya | TS0505B_1 | LED Ceiling Light | # | Turn device on/off 3 times | 230v | 18,81€ | The colors have very low brightness, nearly unusable during daytime |
| Alecto | SMART-HEAT10 | Thermostat | # | Press 7 times on the display | 2xAA (1,5V) | 15,99€ | The device can be paired, without attaching it to a valve. Does not provide many entities. Also, very bad battery lifetime. |
| Tuya | SZ-A60-18W | LED bulb E27 | # | Turn device on/off 3 times | 4,39€ | Brand: Gleco | 500-999 lumen | |
| AVATTO | ME168 | Thermostat | # | Rotate the knob until temperature state is ‘OF’, press and hold the knob for 5 seconds. Wi-Fi icon should flash. | 2xAA (1,5V) | 16,70€ | Set the temperature to maximum (35°C) before installation. |
| Tuya (Moes) | TRV601 | Thermostat | # | In manual mode, turn the knob counterclockwise until the screen displays ‘OF’. Press and hold the middle button for 3 seconds until the WI-FI icon flashes. | 3xAA (1,5V) | 16,41€ | I noticed that it helps to re-insert the batteries, if the device won’t pair. Also, it’s important to first attach the thermostat to the valve and run the adapting process first. This is so far my favorite TRV, as it provides more entities than the other ones. |
| Moes | BHT-002-GA | Thermostat | # | Turn thermostat off, press and hold the temperature down button for +- 8 seconds | 230v | 28,40€ | Very positive review, but in my case the device is spaming the zigbee network… And unfortunately, sometimes there a some temperature spikes, which destroy the history graph in HA. This is also mentioned in the comments of the review. Lucky via this thread, I found a custom firmware that can be flashed via OTA. |
| Tuya | Smart Socket | Plug (incl. power measurement) | # | Pair this device with a long press (5 seconds) on the on/off button | 230v | 2,93€ | |
| Tuya | ZTH08-E | Temperature and humidity sensor | # | Press and hold the reset button on the device for +- 5 seconds | 3xAAA | 5,86€ | |
| Tuya | ZTH01 | Temperature and humidity sensor | # | Press and hold the reset button on the device for +- 5 seconds (until the network indicator at the top of the display starts blinking). | 2xAAA | 2,60€ | In Zigbee2MQTT, recognized as TS0201 |
| Moes | MS-105Z | Smart Dimmer | # | To reset the device you need to have a switch wired between L and S, or short them using a tool like a voltmeter. Press the switch for 10 times, then wait for one second. If successful, you will hear three long beeps followed by a series of short beeps that will continue until the device is paired. | 230v | 8,90€ | |
| Sonoff | ZBMINIR2 | Smart Switch | # | Press the pairing button for 5 seconds, until the signal LED flashes slowly. | 230v | 1,73$ (1,52€) | |
| Tuya (Zemismart) | SPM02V2.5 | Power meter | # | Press the reset button 3~5 seconds til the LED is quickly flashing | 400v | 32,45€ | Unfortunately device is spamming the network a bit. The report interval can be changed on devices with newer firmware version. My device seems to have an older firmware and update is only possible via official hub… |
| Moes | Moes ZS-EUD_1gang | Smart touch dimmer | # | Press and hold On/Off Button for 5 seconds | 230v | 16,01€ | |
| eWeLink | SNZB-04_eWeLink | Contact sensor | # | Press reset key for more than 6s until the indicator is flashing | CR2023 | 2,60€ | It is labeled C3007 on the box. Small device, but very bad battery lifetime. |
| Sonoff | TRVZB | Thermostat | # | Turn the device off and hold down the top button for 3 seconds. The device must first be attached to the valve. | 3xAA | 12,98€ | It’s possible to adjust the valve opening and closing degree. |
| Tuya | TH02Z | Temperature and humidity sensor | # | Press paring button (next to the batteries underneath the cover) for 5 seconds | 2xAAA | 3,50€ | It is labeled TH08Z-B on the box |
| eWeLink | SNZB-02 | Temperature and humidity sensor | # | Press and hold the RESET button for 5 seconds till red LED flashes | 2xAAA | 2,43€ | Got paired as SNZB-02, but it does look like a TH02Z |
| Tuya | TS0203 (black) | Contact sensor | # | Press and hold the reset switch on the device, the pinhole on the side of the device, using the provided reset pin for +- 5 seconds | 2xAAA | 3,70€ | It is labeled ZD06 on the manual. The device is working great, but the quality of the case seems to be very low. |
| Tuya | TS0203 (white) | Contact sensor | # | Press and hold the reset switch on the device, the pinhole on the side of the device, using the provided reset pin for +- 5 seconds | 2xAAA | 2,31 | |
| eWeLink | SNZB-03 | Water Leakage Sensor | # | Press and hold the RESET button for 5 seconds till red LED flashes | 2xAAA | 3,50€ | Got paired as SNZB-03 (motion sensor), but does look like an IH-K665. Switch in HA from occupancy to moisture in the device settings. |
| Tuya | 809WZT | Motion sensor | # | Use a pin to press and hold the “SET button” of the sensor for 5s until the indicator flashes quickly. (button at the bottom, LED is at the front) | 2xAAA | 2,58€ | |
| Zbeacon | TH01 | Temperature and humidity sensor | # | Press and hold the RESET button for 5 seconds till red LED flashes | 2xAAA | 2,31€ | |
| Dycsm | YG400A | Smoke detector | # | Press and hold the RESET button for 5 seconds till LED flashes | 2xAAA | 5,93€ | |
| Tuya | TS0603 | Garage door opener | # | Press reset key for about 10 seconds until the indicator light flashes quickly | 230v | 13,08€ | |
| HOBEIAN | ZG-204ZV | Motion & temperature & humidity sensor | # | Press and hold the RESET button for 3 seconds till LED flashes | 2xAAA | 1.78$ (~1,50€) | Device does not work. Motion is detected every few seconds until the battery is empty. |
| ONENUO (Tuya) | ZP01 | Motion sensor | # | Press and hold the RESET button for 5 seconds till red LED flashes | 2xAAA | 2.58€ | |
| HOBEIAN | ZG-102ZM | Vibration sensor | # | Press and hold the RESET button for 3 seconds till LED flashes | 2xAAA | 2.21$ | |
| Telink Semiconductor (Tuya) | TS0202 | Motion sensor | # | Press and hold the RESET button until LED flashes | 2xAAA | 1.86$ (~1,43€) |